Airmar P48W Manual do Utilizador descarregar pdf

Follow the precautions below for optimal

product performance and to reduce the risk of

property damage, personal injury, and/or death.

WARNING: Always wear safety goggles and a dust

mask when installing.

WARNING: When the boat is placed in the water,

immediately check for leaks around the screws and

any other holes drilled in the hull.

CAUTION: P48W—Operate at 200kHz only.

Operating at any other frequency will permanently

damage the transducer and/or the echosounder.

CAUTION: CHIRP transducer—Always operate the

transducer in water. Operating in air will allow the

transducer to overheat resulting in failure.

CAUTION: Never pull, carry, or hold the transducer by

its cable; this may sever internal connections.

CAUTION: Never strike the transducer with anything

except the palm of the hand to release it.

CAUTION: Never use solvents. Cleaner, fuel, sealant,

paint and other products may contain solvents that can

damage plastic parts, especially the transducer’s face.

IMPORTANT: Read the instructions completely

before proceeding with the installation. These

instructions supersede any other instructions in your

instrument manual if they differ.

Figure 1. Attaching the bracket to the transducer

pivot post (2)

recess (2)

bracket

nuts

machine

screw (2)

slot (2)

sensor

17-499-01 rev. 06 01/18/13

Transom or Trolling Motor Mount

CHIRP or Adjustable Wide-beam Transducer

Models: P48W, TM130M, TM150M, TM210H

U.S. Patent 7,961,522. UK 2 414 077. U.S. Patents Pending

Tools & Materials

Safety goggles

Dust mask

Phillips screwdrivers

Pencil

Electric drill

Drill bits:

Bracket holes 4mm, #23, or 9/64"

Transom hole (optional) 18mm, 11/16", or 3/4"

24 mm or 15/16" or 1"

(Raymarine only)

Cable clamp holes 3mm or 1/8"

Masking tape

Angle finder (some installations)

Marine sealant (suitable for below waterline)

Straight edge

Grommet(s) (some installations)

Cable ties (some installations)

Band clamp

(trolling motor mount) Measure before purchasing ( Figure 9)

Water-based anti-fouling paint (mandatory in salt water)

Record the information found on the cable tag for future reference.

Part No._________________Date___________Frequency________kHz

INSTALLATION INSTRUCTIONSOWNER’S GUIDE &

TM150M

P48W

Applications

• Recommended for boat up to 7m (22’) long

• Not recommended for boats with large inboard engine(s)

• P48W—Not recommended for stepped transoms because the

transducer will be difficult to adjust.

• Vertically orients sound beam on hull with deadrise angle up to 22°

• Adjusts to transom angles from 2° – 22°

• Requires 89mm (3-1/2") of headroom to install

• Bracket protects sensor from frontal impact only

• P48W or TM150M—Trolling motor fitting adapts transducer for

use with a trolling motor or optional Portable Mount Kit

Transom Mount

Attaching the Bracket to the Transducer

1. Insert the sensor’s pivot posts into the recesses on the sides of

the bracket (see Figure 1).

2. Press the two nuts into the slots in the back of the bracket.

3. Align the holes in the sensor, bracket, and nuts. Insert the two

machine screws capturing the nuts. Tighten the machine screws

until the sensor will stay in the “up” (released) position unaided.

Mounting Location

CAUTION: Do not mount in line with or near water intake or

discharge openings or behind strakes, fittings, or hull irregularities

that will disturb the water flow.

CAUTION: Do not mount the sensor where the boat may be

supported during trailering, launching, hauling, or storage to avoid

damaging the transducer’s face.

1 2 3 4 5 6

Resumo do Conteúdo

Página 1 - Transom Mount

Follow the precautions below for optimal product performance and to reduce the risk of property damage, personal injury, and/or death.WARNING: Always

Página 2 - Hole Drilling

allow 76mm• Small aluminum and fiberglass boats (20° transom angle)—Use the 9° shim with the taper up (see Figure 4). If your boat is capable of speed

Página 3 - Releasing the Bracket

3. If the decline in performance is sudden (not gradual), identify the boat speed at which the onset occurred. Return the boat to this speed, then gra

Página 4 - P48W or TM150M Only

Página 5 - Operating: P48W

Página 6 - Maintenance